Phalanx XXV
Moderators: hgm, Rebel, chrisw
-
- Posts: 256
- Joined: Sun May 16, 2010 2:50 am
Re: Phalanx XXV
for some reason I cant get the engine to use weaker settings like slower nps under chessparter interface even with a wb2uci it won't allow me. That's why i was hoping for a work around or a official uci version.
-
- Posts: 27
- Joined: Thu May 01, 2014 12:58 pm
Re: Phalanx XXV
The easy levels, as invoked with the -e commandline parameter, always add oversights and blunders. The rating gap between -e 1 and -e 99 is pretty large, actually. I think -e 1 is even stronger than the slowest limited NPS levels. Not sure how to design this so that it would go to near full strength - perhaps only add blunders between -e100 and -e10, anything above that would just exponentialy raise NPS up to 10000?
Here is a nice article that attempts to map the limited NPS levels to ratings https://www.chess.com/forum/view/chess- ... lanx-xxiii
Here is a nice article that attempts to map the limited NPS levels to ratings https://www.chess.com/forum/view/chess- ... lanx-xxiii
-
- Posts: 27
- Joined: Thu May 01, 2014 12:58 pm
Re: Phalanx XXV
Hm, maybe it's not possible to pass the commandline arguments through the adapter. Would the adapter accept a .BAT or .CMD file that would just contain the 'phalanx25' command with the parameters?
-
- Posts: 256
- Joined: Sun May 16, 2010 2:50 am
Re: Phalanx XXV
I think the a program called inbetween can be used for that but I don't know how to set that up
-
- Posts: 27809
- Joined: Fri Mar 10, 2006 10:06 am
- Location: Amsterdam
- Full name: H G Muller
Re: Phalanx XXV
I think that wb2uci does allow parameters on the command line. It would not be much use for WB engines if it didn't, as many such engines need these parameters. I recall browsing through its documentation some time ago, and it even had an option for putting the 'command' needed to set hash size to what the UCI option requests on the command line instead of sending it through the interface.
-
- Posts: 256
- Joined: Sun May 16, 2010 2:50 am
Re: Phalanx XXV
well wb2uci won't work in chess partner 6.0 keeps freezing
-
- Posts: 27809
- Joined: Fri Mar 10, 2006 10:06 am
- Location: Amsterdam
- Full name: H G Muller
Re: Phalanx XXV
Well, wb2uci is a UCI engine too, so if Chess Partner cannot run uci2wb, there is no guarantee it can run a native UCI engine either.
The first test should alway be whether you can run whatever you want to run from the command line. So when you start uci2wb from the command line, does it respond like a normal UCI engine? If not, you must have configured it wrong.
The natural 'work-around' would of course be to use a decent GUI, which does run all engines without problems.
The first test should alway be whether you can run whatever you want to run from the command line. So when you start uci2wb from the command line, does it respond like a normal UCI engine? If not, you must have configured it wrong.
The natural 'work-around' would of course be to use a decent GUI, which does run all engines without problems.
-
- Posts: 256
- Joined: Sun May 16, 2010 2:50 am
Re: Phalanx XXV
The only reason why I use it because I like the online interface for it the most out of any other that I have tried but seams since the newest version it won't allow phalanx to work